Mô đun mở rộng Omron 8DO Rơ le CP1W-8ER

841 lượt xem

Ngày: 11/07/2016

Tình trạng : Còn Hàng

Thông tin sản phẩm

Mô đun mở rộng 8 đầu ra rơ le

Mã đặt hàng CP1W-8ER

Liên hệ

Đảm bảo 100% hàng chính hãng

Dịch vụ khách hàng tốt nhất

0936.296.483 (hotline)

0936.296.483 (Hỗ trợ kỹ thuật)

Mô đun mở rộng Omron Sysmac 8 đầu ra rơ le dùng cho dòng PLC CP1E,CP1L,CP1H

Mã đặt hàng CP1W-8ER

Thông số kĩ thuật dòng CP1E giá tốt

Performance Specifications

Item CP1E-E[][]SD[]-[]
CP1E-[][]D[]-[]
CP1E-N[][]S[]D[]-[]
CP1E-N[][]D[]-[]
CP1E-NA[][]D[]-[]
Program capacity 2 K steps (8 Kbytes) including
the symbol table, comments,
and program indices of the
CX-Programmer
8 K steps (32 Kbytes) including the symbol
table, comments, and program indices of
the CX-Programmer
Control method Stored program method
I/O control method Cyclic scan with immediate refreshing
Program language Ladder diagram
Instructions Approximately 200
Proc-
essing
speed
Overhead processing time 0.4 ms
Instruction execution times Basic instructions (LD): 1.19 µs min.
Special instructions (MOV): 7.9 µs min.
Number of CP1W-series Expansion
Units connected
CP1E-E10D[]-[]/[]14(S)D[]-[]/[]20(S)D[]-[]: None
CP1E-[]30(S[])D[]-[]/[]40(S[])D[]-[]/[]60(S[])D[]-[]/NA20(S[])D[]-[]: 3 units
Maximum number of I/O points CP1E-E10D[]-[]: 10
CP1E-[]14(S)D[]-[]: 14
CP1E-[]20(S)D[]-[]: 20
CP1E-[]30(S[])D[]-[]: 150 (30 built in, 40 × 3 expansion)
CP1E-[]40(S[])D[]-[]: 160 (40 built in, 40 × 3 expansion)
CP1E-[]60(S[])D[]-[]: 180 (60 built in, 40 × 3 expansion)
CP1E-NA20D[]-[]: 140 (20 built in, 40 × 3 expansion)
Built-in I/O CP1E-E10D[]-[]: 10 (6 inputs, 4 outputs)
CP1E-[]14(S)D[]-[]: 14 (8 inputs, 6 outputs)
CP1E-[]20(S)D[]-[]: 20 (12 inputs, 8 outputs)
CP1E-[]30(S[])D[]-[]: 30 (18 inputs, 12 outputs)
CP1E-[]40(S[])D[]-[]: 40 (24 inputs, 16 outputs)
CP1E-[]60(S[])D[]-[]: 60 (36 inputs, 24 outputs)
CP1E-NA20D[]-[]: 20 (12 inputs, 8 outputs)
Built-in
input
func-
tions
High-
speed
counters
High-speed
counter mode/
maximum
frequency
Incremental Pulse Inputs
10 kHz:
6 counters
5 counters (only for 10 I/O
points)
Up/Down Inputs
10 kHz: 2 counters
Pulse + Direction Inputs
10 kHz: 2 counters
Differential Phase Inputs (4x)
5 kHz: 2 counters
Incremental Pulse Inputs
100 kHz: 2 counters, 10 kHz: 4 counters
Up/Down Inputs
100 kHz: 1 counters, 10 kHz: 1 counters
Pulse + Direction Inputs
100 kHz: 2 counters
Differential Phase Inputs (4x)
50 kHz: 1 counter, 5 kHz: 1 counter
Counting mode Linear mode
Ring mode
Count value 32 bits
Counter reset
modes
Phase Z and software reset (excluding increment pulse input)
Software reset
Control method Target Matching
Range Comparison
Input interrupts 6 inputs (4 inputs only for 10 I/O points)
Interrupt input pulse width: 50 µs min.
Quick-response Inputs 6 inputs (4 inputs only for 10 I/O points)
Input pulse width: 50 µs min.
Normal
input
Input constants Delays can be set in the PLC Setup (0 to 32 ms, default: 8 ms).
Set values: 0, 1, 2, 4, 8, 16, or 32 ms
Built-in
output
func-
tions
Pulse
outputs
(Models
with
transistor
outputs
only)
Pulse output
method and
output frequency
Pulse output function not
included
Pulse + Direction Mode
1 Hz to 100 kHz: 2 outputs
Output mode Continuous mode (for speed control)
Independent mode (for position control)
Number of
output pulses
elative coordinates: 0000 0000 to 7FFF
FFFF hex (0 to 2147483647)
Absolute coordinates: 8000 0000 to 7FFF
FFFF hex (-2147483647 to 2147483647)
Acceleration/
deceleration
curves
Trapezoidal acceleration and deceleration
(Cannot perform S-curve acceleration and
deceleration.)
Changing SVs
during
instruction
execution
Only target position can be changed.
Origin searches Included
Pulse
outputs
(Models
with
transistor
outputs
only)
Frequency PWM output function not
included
2.0 to 6,553.5 Hz (in increments of 0.1 Hz)
with 1 output or 2 Hz to 32,000 Hz (in
increments of 1 Hz) with 1 output
Duty factor 0.0% to 100.0% (in increments of 0.1%)
Accuracy: +1%/-0% at 2 Hz to 10,000 Hz
and +5%/-0% at 10,000 Hz to 32,000 kHz
Output mode Continuous Mode
Built-in analog Analog input Analog function not included Setting range: 0 to 6,000 (2 channels only
for NA-type)
Analog output Setting range: 0 to 6,000 (1 channels only
for NA-type)
Analog adjusters E/N/NA[][]-type: 2 adjusters (Setting range: 0 to 255)
E/N[][]S(1)-type: None
Com-
muni-
cations
B-type Peripheral USB Port Conforming to USB 2.0 B type connector
Transmission
distance
5 m max.
Built-in RS-232C port No built-in RS-232C port Interface: Conforms to EIA RS-232C.
Communications
method
Half duplex
synchronization Start-stop
Baud rate 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Transmission
distance
15 m max.
Supported
protocol
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Built-in RS-485 port No built-in RS-485 port N30/40/60S1-type only
Interface: Conforms to EIA RS-485. 2-wire
sensors
No isolation
Communications
method
Half duplex
synchronization Start-stop
Baud rate 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Transmission
distance
50 m max.
Supported
protocol
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Serial Option port Option Board cannot be
mounted.
N30/40/60 and NA20-type only
1 port
Mountable
Option Boards
One RS-232C port: CP1W-CIF01
One RS-422A/485 port (not isolated):
CP1W-CIF11
One RS-422A/485 port (isolated): CP1W-
CIF12
One Ethernet port: CP1W-CIF41
Communications
method
Depends on Option Board.
synchronization Depends on Option Board.
Baud rate 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Compatible
protocols
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Number of tasks 17
• One cyclic execution task
• One scheduled interrupt task (always interrupt task 1)
• Six input interrupt tasks (interrupt tasks 2 to 7)
• Sixteen high-speed counter interrupt tasks (interrupt tasks 1 to 16)
Maximum subroutine number 128
Maximum jump number 128
Scheduled interrupt tasks 1 interrupt task
Clock Clock function not included.
The time of error occurrence
displays 01-01-01 01:01:01
Sunday
Included.
Accuracy (monthly deviation):
-4.5 min to -0.5 min at ambient
temperature of 55°C,
-2.0 min to +2.0 min at ambient
temperature of 25°C,
-2.5 min to +1.5 min at ambient
temperature of 0°C
Memory
backup
Built-in EEPROM Ladder programs and parameters are automatically saved to built-in EEPROM
A section of the Data Memory Area can be saved to the built-in EEPROM.
Battery backup With
CP1W-BAT01 Battery
(Sold separately)
Battery cannot be mounted. CP1W-BAT01 can be used.
Maximum battery service life: 5 years
Backup Time
Guaranteed value (ambient temperature:
55°C): 13,000 hours (approx. 1.5 years)
Effective value (ambient temperature:
25°C): 43,000 hours (approx. 5 years)
CIO
Area
Input Bits 1,600 bits (100 words): CIO 0.00 to CIO 99.15 (CIO 00 to CIO 99)
Output Bits 1,600 bits (100 words): CIO 100.00 to CIO 199.15 (CIO 100 to CIO 199)
Serial PLC Link Words 1,440 bits (90 words): CIO 200.00 to CIO 289.15 (words CIO 200 to CIO 289)
Work Area (W) 1,600 bits (100 words): W0.00 to W99.15 (W0 to W99)
Holding Area (H) 800 bits (50 words): H0.00 to H49.15 (H0 to H49)
Bits in this area maintain their ON/OFF status when operating mode is
changed.
Auxiliary Area (A) Read-only: 7,168 bits (448 words) A0 to A447
Read/write: 4,896 bits (306 words) in words A448 to A753
Temporary Relay Area (TR) (TR Area) 16 bits: TR0 to TR15
Timer Area (T) 256 timer numbers (T0 to T255 (separate from counters))
Counter Area (C) 256 counter numbers (C0 to C255 (separate from timers))
Data Memory Area (D) 2 Kwords: D0 to D2047
Of these, 1,500 words can be
saved to the backup memory
(built-in EEPROM) using
settings in the Auxiliary Area.
8 Kwords: D0 to D8191
Of these, 7,000 words can be saved to the
backup memory (built-in EEP-ROM) using
settings in the Auxiliary Area
Operating modes PROGRAM mode:
Program execution is stopped.
Preparations can be executed prior to program execution in this mode.
MONITOR mode:
Programs are executed.
Some operations, such as online editing, and changes to present values in
I/O memory, are enabled in this mode.
RUN mode:
Programs are executed.
This is the normal operating mode.

Để xem các sản phẩm bộ lập trình Omron khác tại đây

Để tải tài liệu Omron chính hãng tại đây

NHẬN XÉT SẢN PHẨM