FX3U-2HSY-ADP Mô đun điều khiển vị trí 2 trục

811 lượt xem

Ngày: 18/06/2019

Tình trạng : Còn Hàng

Thông tin sản phẩm

7,683,000

Xin vui lòng liên hệ theo thông tin dưới dây

0816914999 (Liên hệ mua hàng) Email: sales@minhquangelectric.com THỜI GIAN LÀM VIỆC: Thứ 2 - thứ 6 / 8:00 AM - 5:00 PM Thứ 7 / 9:00 AM - 11:00 AM (Email only)

0969.100.802 (Dịch vụ kỹ thuật) Email: services@minhquangelectric.com THỜI GIAN LÀM VIỆC: Thứ 2 - thứ 6 / 8:00 AM - 5:00 PM Thứ 7 / 9:00 AM - 11:00 AM (Email only)

FX3U-2HSY-ADP

Mô đun điều khiển vị trí 2 trục

The FX series offers low cost PLCs with built-in positioning instructions and pulse output blocks that can perform wide-ranging positioning control.
Additionally, dedicated positioning modules for complex control and multi-axis, interpolation control are also available.

High-speed output special adapter

ModelNumber of
controlled axis
Maximum
frequency
Applicable FX PLC
FX
3S
FX
3G
FX
3U
FX
3GC
FX
3UC
FX3U-2HSY-ADPIndependent two axes200kHz××*

Max.
2 units
××

*: When used together with analog or communication adapters, function expansion board is required

Pulse output block

ModelNumber of
controlled axis
Maximum
frequency
Applicable FX PLC
FX
3S
FX
3G
FX
3U
FX
3GC
FX
3UC
FX3U-1PGIndependent one axis200kHz××*3

Max.
8 units
×*1*3

Max.
6 units
FX2N-10PGIndependent one axis1MHz(1 Hz to 1 MHz
differential line driver output)
××
Max.
8 units
×*1*2

Max.
8 units

*1: When connecting to FX3UC, FX2NC-CNV-IF or FX3UC-1PS-5V is required.
*2: FX3UC-32MT-LT(-2): 7 units. FX3UC-**MT/D,FX3UC-**MT/DSS,FX3UC-16MR/D(S)-T: 8 units.
*3: FX3U, FX3UC supported from version 2.20 or later.

SSCNET

ModelNumber of
controlled axis
Maximum
frequency
Applicable FX PLC
FX
3S
FX
3G
FX
3U
FX
3GC
FX
3UC
FX3U-20SSC-HTwo axes
(Independent/Simultaneous)
××
Max.
8 units
×*1*2

Max.
8 units

*1: When connecting to FX3UC, FX2NC-CNV-IF or FX3UC-1PS-5V is required.
*2: FX3UC-32MT-LT(-2): 7 units. FX3UC-**MT/D,FX3UC-**MT/DSS,FX3UC-16MR/D(S)-T: 8 units.

Positioning dedicated unit

ModelNumber of
controlled axis
Maximum
requency
Applicable FX PLC
FX
3S
FX
3G
FX
3U
FX
3GC
FX
3UC
FX2N-10GMIndependent one axis200kHz××
Max.
8 units
×*1*2

Max.
8 units
FX2N-20GMTwo axes
(Independent/Simultaneous)
200kHz

*1: When connecting to FX3UC, FX2NC-CNV-IF or FX3UC-1PS-5V is required.
*2: FX3UC-32MT-LT(-2): 7 units. FX3UC-**MT/D,FX3UC-**MT/DSS,FX3UC-16MR/D(S)-T: 8 units.

For FX2N-10GM/FX2N-20GM positioning teaching panel

ModelProduct
E-20TP-SET0
(with E-20TP-CAB0)
FX2N-10GM, FX2N-20GM
E-20TP-E-SET0
(with E-20TP-CAB0)

Angle control unit

ModelNumber of
controlled axis
Maximum
frequency
Applicable FX PLC
FX
3S
FX
3G
FX
3U
FX
3GC
FX
3UC
FX2N-1RM-SET*1One axis720 divisions/rotation (0.5 degree)
or 360 divisions/rotation (1 degree)
××
Max.
3 units
×*2*3

Max.
3 units
FX2N-1RM-E-SET*1

*1: FX2N-1RM-SET is a Japanese domestic only product. For use overseas, please select FX2N-1RM-E-SET, which supports overseas standards.
*2: Extension cable cannot be used.
*3: When connecting to FX3UC, FX2NC-CNV-IF or FX3UC-1PS-5V is required.

PLC built-in pulse output functions and positioning functions

ItemsFX3SFX3G,FX3GCFX3U,FX3UC
Number of axisTwo axes[FX3G]
Two axes (14/24 points)
Three axes (40/60 points)
[FX3GC]
Two axes
Three axes
Number of controlled axisIndependent two axes[FX3G]
Independent two axes (14/24 points)
Independent three axes (40/60 points)
[FX3GC]
Independent two axes
Independent three axes
Maximum frequency100 kHz100 kHz100 kHz
Programming languagesSequence programsSequence programsSequence programs
Compatible main unitTransistor
output type
main unit
Transistor
output type
main unit
Transistor
output type
main unit
Pulse
output instruction
Pulse Y Output
(PLSY)
Acceleration/Deceleration Setup
Pulse Y Output
(PLSR)
Pulse output typePulse train
(Direction is controlled
by PLC program)
Pulse train
(Direction is controlled
by PLC program)
Pulse train
(Direction is controlled
by PLC program)
Positioning
instruction
Absolute Current Value Read
([D]ABS)
Dog Search
Zero Return
(DSZR)
Zero Return
(ZRN)
○*1○*1○*1
Variable Speed Pulse Output
(PLSV)
Drive to Increment
(DRVI)
Drive to Absolute
(DRVA)
Interrupt Positioning
(DVIT)
××
Batch Data Positioning Mode
([D]TBL)
×○*2
Pulse output typePulse train + directionPulse train + directionPulse train + direction

Details

Details

Details

*1: No DOG search function Decelerate when near point DOG turns ON, and stop when near point DOG turns OFF (Different from zero return operation with zero signal count)
*2: FX3UC-32MT-LT supported from version 2.20 or later.

Optional parts and spare parts

Servo motor connection cable

ModelLengthDescription
E-GMH-200CAB2 m[MR-H series servo amplifer connection cable]
Can direcly connect FX2N-10GM/FX2N-20GM and servo amplifer.
I/O operation signal part has 20-pin connector for connection to Mtisubishi terminal block.
E-GMJ-200CAB2 m[MR-J series servo amplifer connection cable]
Can direcly connect FX2N-10GM/FX2N-20GM and servo amplifer.
I/O operation signal part has 20-pin connector for connection to Mtisubishi terminal block.
E-GMJ2-200CAB1A2 m[MR-J2, MR-J2-Super series servo amplifer connection cable]
Can direcly connect FX2N-10GM/FX2N-20GM and servo amplifer.
E-GMC-200CAB2 m[MR-C series servo amplifer connection cable]
Can direcly connect FX2N-10GM/FX2N-20GM and servo amplifer.
I/O operation signal part has 20-pin connector for connection to Mtisubishi terminal block.
E-GM-200CAB2 m[General purpose connection cable]
Has connector on both sides.
Can connect to general purpose drive unit via Mitsubishi terminal block.

Connector for self-manufactured I/O cable (an electric wire or a crimp tool is not enclosed.)

ModelDescription
FX2C-I/O-CON[Flat Cable Connector]
AWG28 (0.1 mm2): A set of 10 pcsCrimp connector: FRC2-A020-3OS 1.27-pitch 20 coresCrimp tool: Separately arrange the tool manufactured by DDK Ltd.
357J-4674D Main Unit
357J-4664N Attachment
FX2C-I/O-CON-S[Connector for bared wire]
AWG22 (0.3 mm2): 5 setsHousing: HU-200S2-001
Crimp contact: HU-411SCrimp tool: A product manufactured by DDK Ltd. is separately required.
357J-5538
FX2C-I/O-CON-SA[Connector for bared wire]
AWG20 (0.5mm2): 5 setsHousing: HU-200S2-001
Crimp contact: HU-411SA
Crimp tool: A product manufactured by DDK Ltd. is separately required.
357J-13963

Extension connection cable

ModelLengthDescription
FX2N-GM-65EC65 cm[Connection extension cable between PLC and FX2N-10GM/FX2N-20GM]
One cable cable can be used in a system.
Standard connection cable (55mm) is included with FX2N-10GM/FX2N-20GM.
F2-RS-5CAB5 m[Resolver extension cable for FX2N-1RM]
Resolver can be extended up to 100m extension by linking multiple cables.

Connection cable for peripheral devices

ModelLengthDescription
(1) E-20TP-CAB03 m[E-20TP connection cable]
FX2N-10GM/FX2N-20GM (MINI DIN 8-pin) ⇔ E-20TP (MINI DIN 8-pin)
Cable length is different between (1) and (2).
(1) E-20TP-CAB0 (3 m) is included with E-20TP-SET0.
(2) FX-20P-CAB01.5 m

Spare parts

ModelLengthDescription
FX2N-GM-5EC55 mm[Connection cable between PLC and FX2N-10GM/20GM]
One cable is included with FX2N-10GM/20GM.
NHẬN XÉT SẢN PHẨM