FR-A840-7.5K Biến tần 3 pha 400VAC 7.5kw Mitsubishi

Liên hệ

Giao hàng COD toàn quốc

Mô Tả Sản Phẩm

FR-A840-7.5K Biến tần 3 pha 400VAC 7.5kw Mitsubishi

Mã hàng FR-A840-7.5K
Thông số Đầu vào 3 pha 400VAC, đầu ra 3 pha 400VAC, công suất 7.5kw
Đơn giá Liên hệ
Trạng thái Đang bán

For high-quality products

High response

 ● Response speed

Real sensorless vector control 50 Hz*1 [A700:20 Hz]
Vector control 130 Hz*2 [A700:50 Hz]

Example of changes in actual rotation speed with impact load

Fast response terminal

  • *1 : At 3.7 kW with no load. Differs depending on the load conditions and motor capacity.
  • *2 : The option (FR-A8AP, FR-A8AL, or FR-A8TP) is required.
    Speed response: The speed response indicates how fast the inverter follows the change in the speed command. (The larger value indicates the better speed trackability.)

Line control

Line control

Line control is necessary for the machining of elongated products such as paper, thread, wires, all kinds of sheet, and tape. This will respond rapidly to changes in line speed and suppress the occurrences of winding unevenness.
This contributes to a steady supply of high-quality products.

Perform ultra-fine processing

High-speed rotation

 ● Operating frequency

Real sensorless vector control and vector control 400 Hz [A700:120Hz]
V/F control 590 Hz*3 [A700: 400 Hz]

Running frequency

  • *3 : According to the review result of the export control order about frequency changers, the upper limit of output frequency was determined to be 590 Hz for standard models.

Machine tool

Machine tool

Cutting-edge machine tools are harder and thinner than ever before to be applicable to diverse new materials.
High-speed rotation is required more than ever before in order to be applicable for fine and precise cutting on hard and difficult-to-grind materials.

Swiftly move heavy weights

High torque at low speed

 ● Starting torque (When at 0.3 Hz)

Real sensorless vector control 200% (ND rating)*4, Vector control 200% (ND rating)*4 (150% of initial setting for 5.5K and higher)

 ● Zero-speed torque

Vector control 200%. (Select HD rating.)*4

 ● Speed control range

V/F control 1:10 (6 to 60 Hz: Driving)
Advanced magnetic flux vector control 1:120 (0.5 to 60 Hz: Driving)
Real sensorless vector control 1:200 (0.3 to 60 Hz: Driving)
Vector control 1:1500 (1 to 1500 r/min: Both driving/regeneration)

Example of speed-torque characteristics with Real sensorless vector control

  • *4 : Refer to here for the multiple rating setting.

Cranes

Cranes

Cranes are in operation daily at ports carrying fully-laden containers in response to strong demand from all over the world. Our new inverter realizes smooth cargo handling work at low speed and high torque for the slow and stable movements required for heavy objects.

For accurate and stable transport between machines

PM sensorless vector control

 ● What is a permanent magnet (PM) motor?

A PM motor is a synchronous motor with strong permanent magnets embedded in its rotor. The two major PM motor types are: the interior permanent magnet (IPM) motor with its magnets embedded inside the rotor, and the surface permanent magnet (SPM) motor with its permanent magnets attached on the rotor surface.

 PM sensorless vector control

 ● What is PM sensorless vector control?

The speed and magnetic pole positions, the two essential bits of information to control a PM motor, are detected without a sensor (encoder). The speed detection internally-performed in an inverter enables highly accurate control of a PM motor, almost as accurate as an AC servo system, without the need of a sensor (encoder)*5.
Combining with Mitsubishi MM-CF series IPM motors facilitates aspects of high-level control with no encoder such as “simple positioning”*6 and “zero speed torque”.

  • *5 : Speed fluctuation ratio: ±0.05% (digital input)Speed fluctuation ratio
  • *6 : Positional accuracy (with no load) of 1.5K and lower: ±1.8°, 2K and higher: ±3.6°

Comparison of SF-PRF 1.5 kW 4P and MM-CF152

 ● Easy maintenance for sensor (encoder)-less motor

  •  ● No additional cables means less wiring space required.
  •  ● Improved reliability is obtained in unfavorable operating environments. (e.g. high vibration)
  •  ● PM motors are usually smaller and lighter than induction motors.

Transfer of circuit boards

Transfer of circuit boards

The Simple positioning control delivers a precision workpiece, such as a printed substrate, to a precise position.
Transfer of fragile glass substrates can be performed with a highly accurate driving system.

Taking motor performance to the max

Induction motors and magnet motors can be combined freely

 ● The cutting-edge auto tuning function

The PM motor auto tuning function, which has been newly developed, enables sensorless operation of other manufacturers’ permanent magnet (PM) motors.
Operation with all Mitsubishi Electric induction motors and PM motors, in addtion to induction motors and PM motors from other manufacturers*7, is possible. That means you need less motors for spare and stocks.
(With IPM motors other than MM-CF and PM motors manufactured by other companies, starting torque is limited to 50%, and simple positioning control and zero speed torque cannot be used even if tuned.)

*7: Tuning may not be available depending on its motor characteristics.

a801 img 05 01

 ● Low speed, high torque realized with SF-PR motor

By combining with Mitsubishi Electric’s high-performance, energy-saving motor SF-PR, 100% continuous operation is possible from a low speed of 0.3 Hz for inverters of any capacity.
(when using Real sensorless vector control)

a801 img 05 02

 ● Sharing the spare inverter

One spare inverter is enough for the two types of motors (IM and PM).

a801 img 05 03

Reviews

There are no reviews yet.

Be the first to review “FR-A840-7.5K Biến tần 3 pha 400VAC 7.5kw Mitsubishi”

Your email address will not be published. Required fields are marked *