CP1W-CIF01 Mô đun truyền thông RS232 Omron

1.784 lượt xem

Ngày: 11/07/2016

Tình trạng : Còn Hàng

Thông tin sản phẩm

Mô đun truyền thông RS232C

  • Khoảng cách truyền thông: 15m
  • UC1, N, L, CE
  • Mã đặt hàng CP1W-CIF01

1,113,000

Xin vui lòng liên hệ theo thông tin dưới dây

0936.296.483 (Liên hệ mua hàng) Email: sales@minhquangelectric.com THỜI GIAN LÀM VIỆC: Thứ 2 - thứ 6 / 8:00 AM - 5:00 PM Thứ 7 / 9:00 AM - 11:00 AM (Email only)

0969.100.802 (Dịch vụ kỹ thuật) Email: services@minhquangelectric.com THỜI GIAN LÀM VIỆC: Thứ 2 - thứ 6 / 8:00 AM - 5:00 PM Thứ 7 / 9:00 AM - 11:00 AM (Email only)

CP1W-CIF01

Mô đun truyền thông RS232 CP1W-CIF01 dùng cho loại CP1E, CP1L, CP1H

  • Khoảng cách truyền thông: 15m
  • UC1, N, L, CE
  • Mã đặt hàng CP1W-CIF01

Để xem các sản phẩm bộ lập trình Omron khác tại đây

Để tải tài liệu Omron chính hãng tại đây

Thông số kĩ thuật dòng PLC CP1E giá tốt

Performance Specifications

ItemCP1E-E[][]SD[]-[]
CP1E-[][]D[]-[]
CP1E-N[][]S[]D[]-[]
CP1E-N[][]D[]-[]
CP1E-NA[][]D[]-[]
Program capacity2 K steps (8 Kbytes) including
the symbol table, comments,
and program indices of the
CX-Programmer
8 K steps (32 Kbytes) including the symbol
table, comments, and program indices of
the CX-Programmer
Control methodStored program method
I/O control methodCyclic scan with immediate refreshing
Program languageLadder diagram
InstructionsApproximately 200
Proc-
essing
speed
Overhead processing time0.4 ms
Instruction execution timesBasic instructions (LD): 1.19 µs min.
Special instructions (MOV): 7.9 µs min.
Number of CP1W-series Expansion
Units connected
CP1E-E10D[]-[]/[]14(S)D[]-[]/[]20(S)D[]-[]: None
CP1E-[]30(S[])D[]-[]/[]40(S[])D[]-[]/[]60(S[])D[]-[]/NA20(S[])D[]-[]: 3 units
Maximum number of I/O pointsCP1E-E10D[]-[]: 10
CP1E-[]14(S)D[]-[]: 14
CP1E-[]20(S)D[]-[]: 20
CP1E-[]30(S[])D[]-[]: 150 (30 built in, 40 × 3 expansion)
CP1E-[]40(S[])D[]-[]: 160 (40 built in, 40 × 3 expansion)
CP1E-[]60(S[])D[]-[]: 180 (60 built in, 40 × 3 expansion)
CP1E-NA20D[]-[]: 140 (20 built in, 40 × 3 expansion)
Built-in I/OCP1E-E10D[]-[]: 10 (6 inputs, 4 outputs)
CP1E-[]14(S)D[]-[]: 14 (8 inputs, 6 outputs)
CP1E-[]20(S)D[]-[]: 20 (12 inputs, 8 outputs)
CP1E-[]30(S[])D[]-[]: 30 (18 inputs, 12 outputs)
CP1E-[]40(S[])D[]-[]: 40 (24 inputs, 16 outputs)
CP1E-[]60(S[])D[]-[]: 60 (36 inputs, 24 outputs)
CP1E-NA20D[]-[]: 20 (12 inputs, 8 outputs)
Built-in
input
func-
tions
High-
speed
counters
High-speed
counter mode/
maximum
frequency
Incremental Pulse Inputs
10 kHz:
6 counters
5 counters (only for 10 I/O
points)
Up/Down Inputs
10 kHz: 2 counters
Pulse + Direction Inputs
10 kHz: 2 counters
Differential Phase Inputs (4x)
5 kHz: 2 counters
Incremental Pulse Inputs
100 kHz: 2 counters, 10 kHz: 4 counters
Up/Down Inputs
100 kHz: 1 counters, 10 kHz: 1 counters
Pulse + Direction Inputs
100 kHz: 2 counters
Differential Phase Inputs (4x)
50 kHz: 1 counter, 5 kHz: 1 counter
Counting modeLinear mode
Ring mode
Count value32 bits
Counter reset
modes
Phase Z and software reset (excluding increment pulse input)
Software reset
Control methodTarget Matching
Range Comparison
Input interrupts6 inputs (4 inputs only for 10 I/O points)
Interrupt input pulse width: 50 µs min.
Quick-response Inputs6 inputs (4 inputs only for 10 I/O points)
Input pulse width: 50 µs min.
Normal
input
Input constantsDelays can be set in the PLC Setup (0 to 32 ms, default: 8 ms).
Set values: 0, 1, 2, 4, 8, 16, or 32 ms
Built-in
output
func-
tions
Pulse
outputs
(Models
with
transistor
outputs
only)
Pulse output
method and
output frequency
Pulse output function not
included
Pulse + Direction Mode
1 Hz to 100 kHz: 2 outputs
Output modeContinuous mode (for speed control)
Independent mode (for position control)
Number of
output pulses
elative coordinates: 0000 0000 to 7FFF
FFFF hex (0 to 2147483647)
Absolute coordinates: 8000 0000 to 7FFF
FFFF hex (-2147483647 to 2147483647)
Acceleration/
deceleration
curves
Trapezoidal acceleration and deceleration
(Cannot perform S-curve acceleration and
deceleration.)
Changing SVs
during
instruction
execution
Only target position can be changed.
Origin searchesIncluded
Pulse
outputs
(Models
with
transistor
outputs
only)
FrequencyPWM output function not
included
2.0 to 6,553.5 Hz (in increments of 0.1 Hz)
with 1 output or 2 Hz to 32,000 Hz (in
increments of 1 Hz) with 1 output
Duty factor0.0% to 100.0% (in increments of 0.1%)
Accuracy: +1%/-0% at 2 Hz to 10,000 Hz
and +5%/-0% at 10,000 Hz to 32,000 kHz
Output modeContinuous Mode
Built-in analogAnalog inputAnalog function not includedSetting range: 0 to 6,000 (2 channels only
for NA-type)
Analog outputSetting range: 0 to 6,000 (1 channels only
for NA-type)
Analog adjustersE/N/NA[][]-type: 2 adjusters (Setting range: 0 to 255)
E/N[][]S(1)-type: None
Com-
muni-
cations
B-type Peripheral USB PortConforming to USB 2.0 B type connector
Transmission
distance
5 m max.
Built-in RS-232C portNo built-in RS-232C portInterface: Conforms to EIA RS-232C.
Communications
method
Half duplex
synchronizationStart-stop
Baud rate1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Transmission
distance
15 m max.
Supported
protocol
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Built-in RS-485 portNo built-in RS-485 portN30/40/60S1-type only
Interface: Conforms to EIA RS-485. 2-wire
sensors
No isolation
Communications
method
Half duplex
synchronizationStart-stop
Baud rate1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Transmission
distance
50 m max.
Supported
protocol
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Serial Option portOption Board cannot be
mounted.
N30/40/60 and NA20-type only
1 port
Mountable
Option Boards
One RS-232C port: CP1W-CIF01
One RS-422A/485 port (not isolated):
CP1W-CIF11
One RS-422A/485 port (isolated): CP1W-
CIF12
One Ethernet port: CP1W-CIF41
Communications
method
Depends on Option Board.
synchronizationDepends on Option Board.
Baud rate1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, or 115.2
kbps
Compatible
protocols
• Host Link
• 1:N NT Link
• No-protocol mode
• Serial PLC Links (master, slave)
• Modbus-RTU Easy Master
Number of tasks17
• One cyclic execution task
• One scheduled interrupt task (always interrupt task 1)
• Six input interrupt tasks (interrupt tasks 2 to 7)
• Sixteen high-speed counter interrupt tasks (interrupt tasks 1 to 16)
Maximum subroutine number128
Maximum jump number128
Scheduled interrupt tasks1 interrupt task
ClockClock function not included.
The time of error occurrence
displays 01-01-01 01:01:01
Sunday
Included.
Accuracy (monthly deviation):
-4.5 min to -0.5 min at ambient
temperature of 55°C,
-2.0 min to +2.0 min at ambient
temperature of 25°C,
-2.5 min to +1.5 min at ambient
temperature of 0°C
Memory
backup
Built-in EEPROMLadder programs and parameters are automatically saved to built-in EEPROM
A section of the Data Memory Area can be saved to the built-in EEPROM.
Battery backup With
CP1W-BAT01 Battery
(Sold separately)
Battery cannot be mounted.CP1W-BAT01 can be used.
Maximum battery service life: 5 years
Backup Time
Guaranteed value (ambient temperature:
55°C): 13,000 hours (approx. 1.5 years)
Effective value (ambient temperature:
25°C): 43,000 hours (approx. 5 years)
CIO
Area
Input Bits1,600 bits (100 words): CIO 0.00 to CIO 99.15 (CIO 00 to CIO 99)
Output Bits1,600 bits (100 words): CIO 100.00 to CIO 199.15 (CIO 100 to CIO 199)
Serial PLC Link Words1,440 bits (90 words): CIO 200.00 to CIO 289.15 (words CIO 200 to CIO 289)
Work Area (W)1,600 bits (100 words): W0.00 to W99.15 (W0 to W99)
Holding Area (H)800 bits (50 words): H0.00 to H49.15 (H0 to H49)
Bits in this area maintain their ON/OFF status when operating mode is
changed.
Auxiliary Area (A)Read-only: 7,168 bits (448 words) A0 to A447
Read/write: 4,896 bits (306 words) in words A448 to A753
Temporary Relay Area (TR) (TR Area)16 bits: TR0 to TR15
Timer Area (T)256 timer numbers (T0 to T255 (separate from counters))
Counter Area (C)256 counter numbers (C0 to C255 (separate from timers))
Data Memory Area (D)2 Kwords: D0 to D2047
Of these, 1,500 words can be
saved to the backup memory
(built-in EEPROM) using
settings in the Auxiliary Area.
8 Kwords: D0 to D8191
Of these, 7,000 words can be saved to the
backup memory (built-in EEP-ROM) using
settings in the Auxiliary Area
Operating modesPROGRAM mode:
Program execution is stopped.
Preparations can be executed prior to program execution in this mode.
MONITOR mode:
Programs are executed.
Some operations, such as online editing, and changes to present values in
I/O memory, are enabled in this mode.
RUN mode:
Programs are executed.
This is the normal operating mode.
NHẬN XÉT SẢN PHẨM